Together with the official reseller of Pure-Bore® products, EXEL from Bydgoszcz, Poland, Clear Solutions International Ltd participated in “SITPNIG”, the 12th annual Oil & Gas Conference in Cracow, Poland.

Clear Solutions International presented a workshop on the unique Pure-Bore® high performance water based mud system to the audience which consisted of many representatives from the Polish Oil & Gas industry.

Pure-Bore® was already used in several Polish wells and could convince both: The Drilling fluid company and the operator that Pure-Bore® can be used in harsh environments, formations that are difficult to stabilise or to substitute Oil based or Synthetic based muds with significant cost and waste stream reductions. It speaks for itself that the success of this product led a technical specialist from a local Polish Oil company to present about the operator’s experience with “Nano – technological drilling fluids” with which Pure-Bore® is meant. This presentation has shown that Pure-Bore® seems to be the right approach to improve wellbore conditions and to overcome technical issues.

Industrial greenhouses in Europe which grow cut flowers and vegetables for us as consumers are usually heated by boiler systems which require fossil fuel consumption. When combined with the carbon miles of road delivery, the result is a significant “carbon footprint”. Recent efforts to reduce carbon footprint have included growing plants in hot countries but the carbon miles of subsequent air freighting offsets much of the benefits of natural growing conditions. There is however a new development which uses renewable energy in the form of geothermal water to heat industrial greenhouses. Rather than having to drill into a conventional geothermal reservoir which produces steam, the new system can be operated with water as low as 80 degrees centigrade. The heat content of the produced fluid is passed through a heat exchanger at surface and the cooled water is re-injected back into the aquifer in another well. Such a scheme is called a “doublet”. As the produced hot fluid is continuously replaced by cooled injected water in the aquifer, the temperature of the produced fluid decreases. However, if the wells are shut-in periodically, the earth’s heat replenishes the system and it can be produced again. When operated in production and recovery modes, doublets are both renewable and sustainable.

The contribution made by Pure-Bore® to the sustainability of such a system is both in the drilling of the wells and in their production mode. As the aquifer may be located at depths of up to 2000m, oil well drilling rigs must be used to access it. Previously drilling to these depths in Holland also necessitated using hydrocarbon-based drilling muds which have a high carbon footprint compared to water-based fluids. The substitution of OBM by Pure-Bore®in combination with liquid recovery centrifuges has resulted in a drilling operation with a lower carbon footprint, a reduced water demand and a reduced waste stream with lower end-of-life environmental impact. Pure-Bore® also increases the hydraulic efficiency of the drilling fluid which reduces the time to drill and the energy required for the drilling process as well as maintaining a stable well bore until drilling is completed. By helping reduce the operational drilling cost, the sustainability of the well construction and production system is preserved. These environmental and economic advantages are all unique to Pure-Bore® and are not shared by other water-based fluids.

Unlike conventional geothermal reservoirs which generally occur in fractured formations, doublets need to be drilled in sedimentary sand reservoirs with the required porosity and permeability to allow hydraulic flow. As well as sufficient thickness of sand layers, preservation of the original porosity and permeability is essential to allow commercially sustainable flow rates. Pure-Bore® achieves this by preventing permeability reduction in the well bore while drilling. This allows production and injection rates unrestricted by interactions between the drilling fluid and the critical near well bore permeability.

In short, the use of Pure-Bore® in European onshore geothermal wells is reducing the carbon footprint of a necessary element of our modern lifestyle. Think about that the next time you admire those flowers you bought yourself or your partner!


    To find our more about Pure-Bore®Speciality Products or Case Studies or contact us on +44 (0) 1939 235 754


    Sign up for our newsletter to keep up to date with developments at Clear Solutions

  • Clear Solutions during the COVID-19 Pandemic

    At Clear Solutions International Ltd, during the COVID-19 pandemic it is our priority to keep our employees, their families, customers, and suppliers safe and well. We closely monitor the pandemic situation by following local, national and international health authority guidelines and taking the appropriate measures.

    Measures that we have implemented, include additional hygiene facilities for staff, maintaining social distancing within the factory and offices, enabling employees to work from home, avoiding group meetings and using online video conference call tools. These measures allow our teams to continue operations and to follow up with our customers and suppliers on a regular basis.

    We continue to follow government guidance and will adapt our actions accordingly. This requires that we do some things differently, and we need to prioritise our activities so that we can continue to provide the services you need.

    We value your support and ask for your patience.